Product #630 Highly Novolac Chemical Resistant Epoxy Mortar and Chemical Resistant Epoxy Flooring is a 100% solids epoxy Novolac ideal for harsh chemical and solvent resistant applications. Product #630 Highly Novolac Chemical Resistant Epoxy Mortar and Chemical Resistant Epoxy Flooring is ideal for use as a troweled mortar, slurry binder, and coating for concrete and steel in extremely corrosive areas where resistance to 98% sulfuric acid or other strong caustics is needed.
Product #630 Highly Novolac Chemical Resistant Epoxy Mortar and Chemical Resistant Epoxy Flooring is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities.
100% solids, cycloaliphatic-cured Novolac epoxy resin.
Surface Preparation is the most critical portion to any successful resinous system application. All substrates must be properly prepared as outlined in Epoxy.com Surface Preparation Procedures. The Epoxy.com tech service department is pleased to answer any questions.
Will vary with application method.
PHYSICAL PROPERTIES |
|
| Color | Clear, & The Colors Listed Below. Custom colors available. |
| Solids Content | 100% |
| Gloss 60° F | 90 |
| Viscosity | Part "A": 4500-6500 cps Part "B": 60-75 cps Mixed: 1000-1500 cps |
| Mix Ratio | 2A to 1B by volume |
| Pot Life | 20 - 25 minutes @ 75°F |
| VOC | 0% |
Click the picture
of the color card at the side for a larger version of this picture of the color chart.
Please note:
The picture to the right is a photographic reproduction of the color card for this product.
The photo reproduction process and your monitor and/or printer will change these colors.
This chart is to give you an idea of the colors available and not intended for critical color selections.
DRY TIME | |
| Foot Traffic | 6-7 hours |
| Recoat | 8 - 12 hours |
| Service | 3-5 days |
PERFORMANCE PROPERTIES |
|
| Tensile Strength ASTM-D-638 | 4,000 psi |
| Compressive Strength ASTM-D-695 | 11,000 psi |
| Adhesion to concrete ACI Committee 403 | 300 psi - 100% concrete failure |
| Hardness ASTM-D-2240 | 85 Shore D |
| Abrasion Resistance ASTM-C-501 CS-17 Wheel | 30 mg lost |
| Service Temperature MIL- D-3134F | Up to 180-325 degrees F. Dry Heat |
| Impact Resistance Mil-D-3134F § 4.7.3 | 16 ft. Lbs |
| Indentation MIL-D-3134F §4.7.4 | No Indentation |
| Elevated Temperature Resistance MIL-D-3134F § 4.7.5 | Passed |
| Water Absorption ASTM-D-570 (24. Hr. Immersion) | 0.10% |
R-Recommended for immersion service (greater than 6 months). S1- Splash & Spill 7 day clean-up. S2 Splash & Spill 24 hour clean-up. S3 Splash & Spill hourly clean-up. ND - Not Determined.
Chemical |
Resistance Rating |
| Acetic Acid 20% | R |
| Acetone | S3 |
| Aluminum Chloride - 30% | R |
| Aluminum Nitrate - 50% | R |
| Aluminum Sulfate - 50% | R |
| Ammonium Hydroxide- 30% | R |
| Ammonium Sulfate - 50% | R |
| Ammonium Sulfide - 50% | R |
| Barium Sulfate | R |
| Barium Sulfide | R |
| Beer | R |
| Benzene | S2 |
| Benzyl Alcohol | R |
| Black Liquor | R |
| Butyl Acetate | R |
| Brake Fluid | R |
| Butanol (Normal) | R |
| Calcium Chloride | R |
| Calcium Hydroxide | R |
| Citric Acid - 40% | S1 |
| Corn Oil | R |
| Crude Oil - Sour | R |
| Crude Oil - Sweet | R |
| Cutting Oil | R |
| Cyclohexanone | S3 |
| Diacetone Alcohol | S2 |
| Diesel Fuel | R |
| Diethylene Glycol | R |
| Distilled Water | R |
| Ethanol | R |
| Ethyl Acetate | R |
| Ethyl Alcohol | R |
| Ethylene Dichloride | S1 |
| Ethylene Glycol | R |
| Fatty Acids | R |
| Freon | S1 |
| Fuel Oil | R |
| Gasoline - Unleaded regular | R |
| Gasoline -Unleaded premium | R |
| Glucose | R |
| Glycerin | R |
| Glyoxal - 40% | R |
| Heptane | R |
| Hexane | R |
| Hexylene Glycol | R |
| Hydraulic Fluid | R |
| Hydrochloric Acid -10% | R |
| Hydrochloric Acid-36% | R |
| Hydrogen Peroxide 5% | R |
| Iodine | R |
| Isobutyl Alcohol | R |
| Isopropyl Alcohol | R |
| JP-4 Jet Fuel | R |
| JP-5 Jet Fuel | R |
| Kerosene | R |
| Ketchup | R |
| Lactic Acid | R |
| MAK | ND |
| Methyl Ethyl Ketone | R |
| Methanol | R |
| MIBK | R |
| Mineral Spirits | R |
| MTBK | R |
| Nitric Acid - 10% | R |
| Oxalic Acid | R |
| Peanut Oil | R |
| Perchloroethylene | R |
| Phosphoric Acid 10% | R |
| Phosphoric Acid 75% | R |
| Phosphoric Acid 85% | R |
| Power Steering Fluid | R |
| Skydrol | R |
| Sodium Hydroxide - 50% | R |
| Sodium Hydroxide - 70% | R |
| Sodium Hypochlorite 10% | R |
| Sodium Nitrate - 50% | R |
| Sulfarnic Acid | R |
| Sulfuric Acid 10% | R |
| Sulfuric Acid 50% | R |
| Sulfuric Acid 70% | R |
| Sulfuric Acid-98% | R |
| Toluene | R |
| Tomato Juice | R |
| Transmission Fluid | R |
| Urine | R |
| Vinegar | R |
| Vinyl Tolene | R |
| White Liquor | R |
| Xylene | R |