HTML;
include $_SERVER['DOCUMENT_ROOT'].'/includes/header.php';
?>
Epoxy.com Product #1 All Purpose Epoxy Coating in a Burlington, Vermont Water Plant
Product #1 All Purpose Epoxy Floor and Tank Coating a two component, industrial strength zero (0) VOC, 100% solids epoxy Hi-Build epoxy coating used to coat concrete, steel and most common construction materials. Excellent for use in high foot traffic and light to moderate forklift traffic areas where abrasion resistance is required; for protection against mild corrosion and as a decorative waterproof coating for walls, floors, tanks, etc. It can be broadcast with appropriate silica sand (contact Epoxy.com Technical Support for a recommendation), to create a thicker flooring system in high abrasion situations.
Epoxy.com Product #1 All Purpose Epoxy Coating on Plywood walls and Floors. Installation and Picture by: Suwannee River Rendezvous Resort & Campground
Surface to receive Product #1 - 100% Solids, VOC All Purpose Epoxy Floor and Tank Coating, must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil free blast immediately prior to application. See Epoxy.com Surface Preparation Guide form more details.
Temperature of Product #1 - 100% Solids, VOC All Purpose Epoxy Floor Coating, must be 50 °F or above at time of mixing. Stir each component separately before blending. Mix two parts by volume of Part A with one part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle.
Epoxy Primer Product #899 (or for a more chemical resistant primer Product #12) is recommended for concrete surfaces. Allow primer to cure until it is tack-free. Then apply Product #1 - 100% Solids, VOC All Purpose Epoxy Floor and Epoxy Coating, with a roller, brush, or spray equipment. Two coats are recommended. Apply at a rate of 160 to 200 SF Per gallon per coat (8-10 mils) with 2 coats recommended. Seven days cure time is required to reach maximum chemical resistance. For more information before installing please see installation tips.
DO NOT apply at temperatures below 50° F. Surface must be dry.
Product #1 All Purpose Epoxy Coating on the floor of Tri-Town Water District (Vermont) Floor
Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.
All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent
APPLICATION PROPERTIES @77° F |
|
| Mix Ratio | 2:1 By Volume |
| Viscosity (mixed) | 950 CPS |
| Pot Life (200 gr.) in minutes @70° F. | 30-40 (normal cure) |
| VOC Content | "0.0" (zero) |
| Recommended Application Rate | 160-200 SF per gallon per coat |
| Set Time in Hours @ 70°F. | 10-12 (normal cure) |
| Initial Cure | 24 Hours |
| Final Cure | 5 Days |
| Packaging Unit Size | 3 gal. 15 gal. |
| Standard Colors | See Color Chart |
| Typical Coefficient of Friction-Rubber Shoe Surface with Epoxy.com Product # 50 Anti-skid Fine Non-Skid Added | ASTM F-489 |
| Static Friction w/ Saltwater Solutions on surface | 0.90-0.97 |
| Static Friction w/ oil on Surface | 0.72-0.75 |
| Sliding Friction w/ Saltwater Solution on Surface | 0.87-.090 |
Click the picture
of color card at the side for a larger version of this picture of the
color chart.
Please note:
The picture to the right is a photographic reproduction
of the color card for this product. The photo reproduction process and
your monitor and/or printer will change these colors. This chart is to
give you an idea of the colors available and not intended for critical
color selections.
Epoxy.com a division of Epoxy Systems, Inc. certifies that Product #1 - 100% Solids, VOC All Purpose Epoxy Coating, meets or exceed LEED requirements as summarized below:
Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.
Epoxy Coating Installation Guide
