Since 1980 we have added hundreds of products. You can find a complete listing of these products at www.epoxy.com/products.aspx. Need some help to find the right product for your job, give out Technical Support Department a call at 352-533-2167. Our Technical Support Department can help you with the selection, specification, installation, and maintenance of our products. For a complete listing of all Our Products see www.epoxy.com/products.aspx.
Product #1 All Purpose Coating is a 100% solids epoxy Hi-Build epoxy resin and epoxy hardener coating system is used for high foot and light forklift traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, floors, tanks, etc. Available in normal, fast, and Cold Temperature Cure versions. Zero (0) VOC Epoxy Resin and Epoxy Hardener Coating (sometimes called epoxy resin paint). Meets the lowest Federal and State Low VOC requirements. This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.
Epoxy: Product #1 Fast - is a shorter potlife, and faster setting version of Product #1, This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.
Epoxy: Product #1 Cold Temperature Cure Epoxy Coating is a version of Product #1 Epoxy Resin with a cold temperature Epoxy Hardener that sets even faster than Product#1 Fast Epoxy Coating. Product #1 Cold Temperature Cure Epoxy Coating is used in colder temperatures, or where an very fast cure is required. This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.
Epoxy: Product #1W is a two component, 100% solids epoxy hi-Build resin and epoxy hardener coating system used for high indoor traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, tanks, etc. Zero (0) VOC Epoxy Coating (sometimes called epoxy paint). Meets the lowest Federal and State Low VOC requirements. This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.
Epoxy: Product #2 Chemical Resistant Coating is a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkalines for both interior and exterior applications. Available in normal, fast, and Cold Temperature Cure. Zero (0) VOC Epoxy Resin Coating (sometimes called epoxy resin paint). Meets the lowest Federal and State Low VOC requirements. This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.
Epoxy: Product #2 Fast is a shorter potlife, and faster setting version of Product #2. Uses a fast cure epoxy hardener. This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.
Epoxy: Product #2 Cold Temperature Cure is a version of that sets even faster than Epoxy.com Product#2 Fast Cure. Typically used in colder temperatures, or where an very fast cure is required. Uses a cold (winter) temperature epoxy hardener (cure). This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.
Product #2W Chemical Resistant Wall Coating is a two component, 100% solids epoxy chemical resistant coating used to protect chemical concrete, steel and other structural materials from non-oxidizing acids and alkalines for both interior and exterior applications. This epoxy resin meets Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 402 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.
Product #10 Lo-Mod Adhesive and Mortar Binder is a 100% solids epoxy has a low modulus of elasticity (flexibility) and is Low Viscosity. An adhesive used as a binder for epoxy resin and epoxy hardener mortar systems in patching and grouting applications, as a seal coat for non-skid surfaces outside, and as a primer to insure high bond strength for coatings and patches.
Product #10 Fast Curing Version
Product #10 Cold Temperature Curing Version
Product #11 Epoxy Joint Filler is a 100% solids flexible epoxy joint filler for saw-cut joints of concrete slabs on grade, or to repair existing slabs. Product #11 Epoxy Joint Filler absorbs the impact and shock of heavy loads and steel wheeled traffic, preventing erosion of control joint edges.
Product #12 Epoxy Primer is a two component, seamless 100% solids epoxy resin and epoxy hardener primer system with High Chemical Resistance and High Bond Strength. The epoxy may be applied as a primer for most High End Industrial coatings, like Epoxies, MMA, Polyurethane's, Vinyl Esters, Polyesters, etc.
Product #15 Chemical Resistant Flooring Resin - a two component, seamless 100% solids epoxy resin and epoxy hardener resurfacing system with High Chemical Resistance. It may be applied as a coating, or combined with silica sand or Epoxy.com multi-colored quartz aggregate to produce a durable, easy to maintain floor, on both new and old surfaces. Product #15 Chemical Resistant Flooring Resin has superior clarity and UV stability.
Product #17 Decorative Stone Overlay Adhesive Resin - a two component, 100% solids high-mod epoxy adhesive used for bonding stone and other aggregates in all types of flooring applications. Some uses would include patios, pool decks, walkways and other areas where a long wearing and decorative system is desired.
Product #18 General Purpose Epoxy - a hard set epoxy resin and epoxy hardenr compound formulated for general use. Product #18 cures at room temperature and is a low viscosity system. This durable, resilient material requires no post curing to achieve permanent bond strength. Mixing ratio of 1 to 1 makes this product easy to use. Product #18 General Purpose Epoxy solves many difficult bonding, and epoxy mortar problems. Product has the ability to bond to a variety of substrates including cannot dry and hard to dry surfaces.
Product # 24 Pigmented Mortar is a multipurpose colored epoxy binder for Epoxy Resin - Epoxy Hardener Mortar Systems This all purpose epoxy resin and epoxy hardener is characterized as an excellent general purpose material with good clarity and color retention. It is essentially odorless and can therefore be used in occupied areas.
Product #24 Fast Pigmented Mortar - Fast Cure
Product #24 Cold Pigmented Mortar - Cold Temperature Cure
Product #28 Epoxy Mortar - Honey Clear Mortar 4:1 Ratio a multipurpose colored epoxy binder for Epoxy.com Mortar Systems This all purpose epoxy resin is characterized as an excellent general purpose material with good clarity and color retention. It is essentially odorless and can therefore be used in occupied areas.
Product #32 Flexible Epoxy Resin Membrane is a flexible resin used as an epoxy membrane and as a Product #32 mortar. Product #32 Flexible Epoxy Resin Membrane is a two component, 100% solids epoxy used as a base in many Epoxy.com Floor and Mortar Systems. Product #32 Flexible Epoxy Resin Membrane resists cracking caused by horizontal substrate movement, providing a crack resistant, resilient, sound absorbent, waterproof, durable floor. Product #32 Flexible Epoxy Resin Membrane offers stress-relieving properties for floor slabs that show movement or vibration. Product #32 is excellent for use in areas such as mechanical equipment rooms, large animal rooms and activity centers.
Product # 33 Epoxy Block Filler
Product #100 Anti-Moisture Entrapment System uses a unique epoxy technology which allows the contractor to install epoxy system on new concrete (4-5 days old) without fear of moisture entrapment. Product #100 Anti-Moisture Entrapment System exhibits greater than 100 times the permeability of standard epoxy slurries and mortars. Product #100 Anti-Moisture Entrapment System is used as a base for Epoxy.com Chip and Quartz systems and as a binder for Epoxy.com Resinous Mortar Systems, when moisture is a concern.
Product #201 Oil Stop Primer for instances petroleum can penetrate the surface of a two component, epoxy-amine undercoating designed to be compatible with petroleum based oil and greases. In many instances petroleum can penetrate the surface of concrete floors to the extent that the oil may not be removed by surface cleaning. If untreated, this oil may migrate back to the surface to cause a delamination.
Coal Tar Epoxy Product #209 is a two component 100% solids epoxy coating designed for applications to petroleum contaminated concrete, coating asphalt based surfaces, clean concrete, cement, and properly prepared steel.
Product #214 Tabletop Resin - an all-purpose, low viscosity epoxy resin ystem for coating wooden counter tops, tabletops, bar tops and similar applications. Product #214 Tabletop Resin forms a glossy, hard surface, which is resistant to stains. Product #214 Tabletop Resin has excellent clarity and color retention. It is essentially odorless and can therefore be used in occupied areas
Product #224 Water Cleanable Epoxy Resin Mortar Resin is a user friendly, water cleanable, 100% solids epoxy grout and adhesive. Used for grouting ceramic tile, brick pavers, and stone, it is supplied in pre-packaged kits containing resin, hardener, and (in the Product #225 Water Cleanable Epoxy Mortar Resin Kit) mineral fillers that produce a dense, uniform seal. Typical applications for #224 require resistance to thermal shock, chemicals, and heavy traffic including meat packers, breweries, canneries, bottlers, CIP areas, and pharmaceutical formulators. Product #225 Water Cleanable Epoxy Mortar Resin Kit is designed primarily for applications where you for one reason or another want to use a local aggregate instead of the optimized aggregate that is comes with the Product #225 Water Cleanable Epoxy Resin Mortar Kit. Product #224 Water Cleanable Epoxy Mortar Resin cannot be used without the addition of aggregate so unless you have a special aggregate you want to use be sure to order Product #225 Water Cleanable Epoxy Resin Mortar Kit
Product #225 Water Cleanable Epoxy Resin Mortar Kit - includes Product #224 Water Cleanable Epoxy Mortar Resin along with the aggregate. Mix the three components together for a ready to use system. Product #225 Water Cleanable Epoxy Resin Mortar Kit is a user friendly, water cleanable, 100% solids epoxy grout and adhesive. Used for grouting ceramic tile, brick pavers, and stone, it is supplied in pre-packaged kits containing resin, hardener, and (in the Product #225 Water Cleanable Epoxy Mortar Resin Kit) mineral fillers that produce a dense, uniform seal. Typical applications for #225 require resistance to thermal shock, chemicals, and heavy traffic including meat packers, breweries, canneries, bottlers, CIP areas, and pharmaceutical formulators.
Product #231 - Water Emulsion Primer and Sealer is a water based epoxy primer/sealer designed to have maximum resin penetration into concrete surfaces to provide high bond strength and adhesion. Product #231 Water Emulsion Primer and Sealer has very low odor and, therefore, can be used in occupied areas. Product #231 Water Emulsion Primer and Sealer has the ability to be applied to recently poured (green) concrete and achieve excellent adhesion. Product #231 Water Emulsion Primer and Sealer is ideal for both new and old concrete surfaces. It is used as a primer for Epoxy.com High Build and Thin Film Coating Systems. Replaces Product #222.
Product #235 Chemical Resistant Novolac Epoxy Resin Tile Grout and Adhesive is a highly chemical resistant, industrial grade, Novolac epoxy grout for ceramic tile, quarry tile, brick pavers, and stone. Product #235 Chemical Resistant Novolac Epoxy Resin Tile Grout and Adhesive is supplied in pre-packaged kits containing resin, hardener, and mineral fillers that produce a dense, uniform seal. Typical applications for Product #235 Chemical Resistant Novolac Epoxy Resin Tile Grout and Adhesive require superior resistance to thermal shock, chemicals, and heavy traffic found in the harsh environments of dairies, bakeries, meat packers, breweries, canneries, bottlers, distilleries, and pharmaceutical plants
Product #301 Injection Epoxy Resin, low Modulus - a 100% solids low viscosity epoxy adhesive used to restore cracked structural concrete by the pressure injection method and to grout cracks in a horizontal plane by gravity.
Product #301SC a longer Potlife version of Product #301
Product #301Cold a faster version of Product #301 typically used in Cold Temperature Cure applications, or where a very fast set is needed
Product #315 Chip Flooring Product #315 is a seamless, plural component, liquid applied, 100% solids polymeric colored flake floor resurfacing system with superior wear, and chemical resistance. Product #315 with "multi-colored" flakes produces a durable, easy to maintain floor, on both new and old surfaces.
Product #315BC Polymeric Coating and Base Coat for the 315Chip Flooring System. It can also be used as a stand alone coating. If Product #315BC is used as a stand alone coating over concrete, it is recommended that you first prime with Product #899 Primer.
Product #315BC - Fast Same as Product #315BCPolymeric Coating for Base Coat for the 315Chip Flooring System, but with a fast cure.
Product #315BC-Cold Similar to Product #315BC Polymeric Coating for Base Coat for the 315Chip Flooring System, but with a cold temperature cure.
Product #629 Chemical Resistant Conductive Flooring is a 100% solids epoxy Novolac Conductive coating ideal for severe chemical and solvent storage requiring conductive and spark proof surfaces. Applied at a nominal 1/16 inch, the Product #629 Chemical Resistant Conductive Flooring offers the superior chemical resistance of a Novolac Resin System while maintaining a conductive surface.
Product #630 Novolac Coating/Mortar Binder - a 100% solids epoxy Novolac ideal for harsh chemical and solvent resistant applications. It is ideal for use as a troweled mortar, slurry binder, and coating for concrete and steel in extremely corrosive areas where resistance to 98% sulfuric acid or other strong caustics is needed. Product #630 Novolac Coating/Mortar Binder is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities.
Product #632 Novolac Control Joint Filler is a 100% solids flexible Novolac epoxy Chemical Resistant joint filler for saw-cut joints of concrete slabs on grade.
Product #633 Novolac Coating is a 100% solids epoxy Novolac coating ideal for harsh chemical and solvent resistant applications. It is used in secondary containment, solven storage, pump pads, trenches, and other high exposure areas. It is ideal for use as a protective coating for concrete and steel in the extremely corrosive areas of chemical plants and pulp mills secondary containment areas, water and waste treatment, and gas and electric utilities. Product #633 Novolac Coating is commonly used as a seal coat for Epoxy.com MORTAR SYSTEMS where chemical resistant performance is required.
Epoxy.com Product #671 Conductive Epoxy Resin Primer/Sealer is a low viscosity, two component, carbon filled, polyamide modified conductive primer/sealer formulated with special wetting agents to provide maximum penetration into concrete surfaces. Epoxy.com Product #671 Conductive Epoxy Resin Primer/Sealer is ideal for both new and old concrete surfaces. Epoxy.com Product #671 Conductive Resin Primer/Sealer provides excellent resistance to wear, and can be used either alone or as a conductive sealer or as a conductive primer when used with Product #674 Electro-Static Dissipating Urethane Topcoat and Epoxy.com Conductive Systems.
Product #672 Conductive Epoxy Resin is a two component, 100% solids epoxy/aggregate material that utilizes the latest in conductive floor technology. Product #672 Conductive Epoxy Resin can be installed as a coating or as a component to Epoxy.com Flooring Systems. It can also include Epoxy.com Elastomeric Membranes to produce waterproof, crack resistant Systems. Typical Uses of include: Ammunitions Facilities, Paint and Solvent Storage Areas, Electronic Component Plants Hazardous Materials Storage Areas
Product #675 Electrostatic Dissipating Water Borne Epoxy Topcoat is a pigmented, water emulsion epoxy electro-static dissipative finish designed to have maximum penetration into concrete surfaces to provide high bond strength and adhesion. It has very low odor and can be used in occupied areas as a finish sealer in Thin-Film Electro-Static Dissipative Coating Systems.
Product #676 Novolac Epoxy Chemical Resistant Conductive Epoxy Resin Floor Coating is a 100% solids - Zero (0) VOC epoxy Novolac Chemical resistant conductive (anti-sparking) epoxy flooring and floor coating system ideal for severe chemical and solvent storage requiring a chemically resistant conductive and spark resistant surface.
Product #677 Electro Static Dissipative (ESD)/ Conductive Epoxy Resin Coating is a pigmented, water-based epoxy coating designed to achieve either an electro-static dissipative (ESD) finish or conductive finish by modifying the underlying system components and thickness. Product #677 has very low odor making it suitable for use in occupied buildings and has high bond strength and adhesion to concrete and other surfaces.
Product #720 Cove Base Binder - can be used to install an integral cove base for most Epoxy.com Flooring Systems, to provide seamless wall to floor protection.
Product #830 Moisture Vapor treatment is a two component modified epoxy system designed to seal concrete and reduce moisture vapor transmission prior to applying finished flooring. Product #830 Moisture Vapor treatment has proven to reduce moisture vapor emissions and be resistant to damage from high alkalinity. Product #830 Moisture Vapor treatment is an environmentally friendly material containing no hydrocarbons or other solvents making it zero (0) VOC.