Epoxy.com Product #699
Low Viscosity Methyl Methacrylate (MMA) Sealer
Chemical Resistant Sealer Top Coating - Superior Flow & Leveling, Scratch Resistant
Description
Epoxy.com Product #699 Low Viscosity Methyl Methacrylate (MMA) Sealer is a 100% reactive, low viscosity methyl methacrylate resin developed as a chemical resistant sealer/topcoat. Epoxy.com Product #699 Low Viscosity Methyl Methacrylate (MMA) Sealer cures to a hard, scratch and wear resistant surface and is specifically designed for dry service in areas subjected to high traffic such as manufacturing areas, aisles, lobbies, service areas, and numerous other applications.
Advantages
- UV Resistant
- Superior Scratch and Wear Resistance
- Higher Temperature Resistance
- Superior Chemical Resistance.
- Lower Viscosity - Excellent Flow for Leveling
- Fast Setting - Less than 1 Hour
- 100% Reactive
Considerations
- Concrete must be clean and free of all oil, grease, paint, dirt, sealers, laitance and any other foreign material that might interfere with proper bonding.
- Do not store Epoxy.com Product #699 Low Viscosity Methyl Methacrylate (MMA) Sealer in direct sunlight, storage temperature must be less than 80 ° F.
- On or below grade applications should have a moisture vapor barrier under the slab. Maximum vapor transmission must be less than 3 lbs per ASTM F-1869 and less than 80% RH per ASTM F-2170.
Composition
Epoxy.com Product #699 Low Viscosity Methyl Methacrylate (MMA) Sealer is a 100% Solids Methyl Methacrylate (MMA).
Surface Preparation
Good surface preparation is the first necessary step to successful installation of all Resinous Flooring System. All substrates must be clean and free of all oil, grease, paint, dirt sealers laitance and any other foreign matter that may interfere with proper bonding. Follow the directions for surface preparation as outlined in Epoxy.com Surface Preparation Guide.
Color Selection
Can be used clear (with a slight blue tint). Color packs are available in selected colors. Color pack mix ratio is 1 QT color pack per 5 gallon pail of Epoxy.com Product #699 Low Viscosity Methyl Methacrylate (MMA) Sealer and Top Coating Resin.
Mixing and Installation
Epoxy.com Product #699 Low Viscosity Methyl Methacrylate (MMA) Sealer and Top Coating Resin requires the adding of Epoxy.com Product #695 Hardening Powder. to start the hardening process. The amount of hardener must be adjusted to the respective surface temperature (see table below). At temperatures below 40°F, Epoxy.com Product #696 Accelerator must be used, contact Epoxy.com Technical Support for a recommended dosing.
In order to achieve the best curing it is necessary to apply Epoxy.com Product #699 Low Viscosity Methyl Methacrylate (MMA) Sealer with a short nap roller. Coating thickness should be a minimum of 10 mils and maximum of 20 mils (80-160 sq ft/gal.) depending on the profile of the base material. One hundred (100) sq ft/gal. is average. If the coating exceeds 20 mils, the top coat may remain visibly blue or yellow and surface cracks are possible. It is best to spread material with a notched trowel or squeegee to the desired thickness, and roll in one direction, then roll in a 90° pattern. This will reduce the occurrence of roller marks in the top coat.
Temp. (°F) of Resin, Air & Floor Surface
Hardener % by Wt. Based on Wt. of #699 Resin |
Hardener by Vol. (oz.) Based on Gallon of #699 Resin |
Pot Life (min.) |
Hardness Time (min.) |
|
| +40 | 1.5 | 3 | Approx. 40 | Approx. 55 |
| +50 | 1.5 | 3 | Approx. 30 | Approx. 40 |
| +60 | 1.5 | 3 | Approx. 25 | Approx. 35 |
| +70 | 1.0 | 1.8 | Approx. 15 | Approx. 20 |
Hardener concentration greater than 2% by weight or 4 oz. by volume might lead to discoloration (yellowing). Epoxy.com recommends waiting 2 hours between coating and sealing. Coating work has to be continued after the complete hardening of the previous layer.
Physical Properties
| Basic Material | Methyl Methacrylate Resin (MMA) |
| Percent Reactive | 100% |
| Appearance | Clear Low Viscosity Liquid (with slight blue cast) |
| Viscosity, cps@ 73°F | 185-195 |
| Weight per Gallon | 8.35 lbs |
| Recoat Time | 2 hours± |
| Pot Life Min (Varies with Temp) |
15-40 |
| Cure Rate (min) | 20-55 |
| Heat Resistance | 216°F |
| Shore D Hardness | 75-80 |
Cleanup
Clean tools and equipment with lacquer thinner or MEK. Consult Material Safety Data Sheet for safety and health precautions.
Coverage
100 square feet per gallon, average.
Availability
Contact Epoxy.com Customer Service Department
Maintenance
Epoxy.com Product #699 Low Viscosity Methyl Methacrylate (MMA) Sealer is considered to be a very low maintenance flooring system. With some textures and conditions it may have to be cleaned by bristle brush or low pressure wash. Due to the thermoplastic character of Methyl Methacrylate (MMA) resins, you may get black marks from fork lifts and tire skidding.
Storage
Store Epoxy.com Product #699 Low Viscosity Methyl Methacrylate (MMA) Sealer in a cool and dry place, below 80°F, out of direct sunlight. Do not store near open flame or food. Shelf life is 4-6 months in the original unopened containers.
Tips
Adequate cross ventilation should be provided. Good ventilation during the processing ensures a good cross linking and hardening. Read, understand and follow Material Safety Data Sheets and Application Instructions prior to use.
Use only as directed. If substrate and/or material temperature is above 90°F, DO NOT apply material.
Technical Support
Call Epoxy.com Technical Support Department with any technical support questions.