Epoxy Wall Coating, 100% Solids High-Build
Thick Bodied Epoxy Coating (Paint) for Verticals and Overhead
Epoxy.com Product #1W (Wall Grade)
EPOXY COATING DESCRIPTION
Product #1W High Build Epoxy Wall Coating - epoxy coating for walls, is a two component, 100% solids epoxy Hi-Build epoxy wall coating used for high indoor traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, tanks, etc.
Epoxy Coating Installation Guide
Epoxy Coatings Calculator
EPOXY COATING ADVANTAGES
- Moisture Insensitive
- Ceramic like finish
- Thicker Bodied Epoxy Makes it an Excellent for Floors and Ceilings
- Solvent Free
- Waterproof
- Extremely Durable
- Chemical Resistant
SURFACE PREPARATION FOR EPOXY COATING
Bath House Construction project. Picture compliments of Suwannee River Rendezvous Campground
Epoxy.com Product #1W on Walls and
Chip Flooring on the floor.
Surfaces to receive Product #1W High Build Epoxy Wall Coating must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, mechanical abrasion, or acid etching. Remove water and dust from all surfaces with an oil-free blast immediately prior to application.
EPOXY COATING MIXING INSTRUCTIONS
Temperature of Product #1W High Build Epoxy Wall Coating must be 50° F or above at time of mixing. Stir each component separately before blending. Mix 4 parts by volume of Part A with 1 part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle.
EPOXY COATING APPLICATION
Apply Product #1W High Build Epoxy Wall Coating with a roller, brush, or spray equipment. Two coats are recommended. Thickness per coat should be 7-10 mils. Seven days cure time is required to reach maximum chemical resistance.
EPOXY COATING LIMITATIONS
DO NOT apply Product #1W High Build Epoxy Wall Coating at temperatures below 50° F. Surface must be dry.
EPOXY COATING SAFETY PRECAUTIONS
Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.
EPOXY CLEAN UP
Clean Product #1W High Build Epoxy Wall Coating from all tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.
EPOXY COATING APPLICATION PROPERTIES @77° F |
|
| Mix Ratio | 4:1 By Volume |
| Viscosity (mixed) | 2000 -2500 CPS |
| Pot Life (200 gr.) | 40-50 minutes |
| Tack Free to Touch | 8 to 10 Hours |
| Initial Cure | 24 Hours |
| Final Cure | 7 Days |
| Packaging Unit Size | 1.25 gal. unit, 5 gallon unit |
| Standard Colors | White, Light Gray, Dark Gray, Taupe, Sand, Old Gold, Mocha, Brick Red, Slate Blue, Colonial Green, Deep Blue, Black, Safety Yellow |
Click
the picture of color card below for a larger version of this picture
of the color chart.
Please note: The picture to the right is a photographic reproduction of the
color card for this product. The photo reproduction process and your
monitor and/or printer will change these colors. This chart is to give you
an idea of the colors available and not intended for critical color selections.
EPOXY TENSILE PROPERTIES | |
|---|---|
| Tensile Strength (ASTM D-638) | 5500 psi. min. |
| Elongation | 4-5% |
Other customers who visited this page also visited:
- Epoxy.com Product #1 - All Purpose Epoxy Coating
- Epoxy.com Product #2 - Chemical Resistant Epoxy coating.
- Epoxy.com Product #315BC - Chip Flooring System Base coat.
- Epoxy.com Product #633 - Epoxy Novolac Coating - extremely chemical resistant
- Epoxy.com Chip Flooring System
- Epoxy.com Coatings Page.