Epoxy.com Product #1 ESD-NT
Product #1 ESD-NT is a 100% solids bis-A epoxy floor coating designed to provide electrostatic control properties to various surfaces including concrete or other non-conductive substrates. Product #1 ESD-NT has good chemical resistance and is ideal for any areas requiring electrostatic dissipative or conductive surfaces, provides excellent bond to concrete as well as impact and wear resistance. Application over a non-conductive primer or basecoat will transmit ESD readings of less than 1,000,000,000 ohms through Product #1 ESD-NT. Application over Product #668 CONDUCTIVE PRIMER will transmit conductive readings of less than 1,000,000 ohms through Product #1 ESD-NT.
100% solids bis-A epoxy resin and fillers.
Product #1 ESD-NT will yield approximately 20-32 mils when spread at 50-80 ft2 per gallon.
Product #1 ESD-NT is available in ESD-NT Standard Colors only, contact Epoxy.com for color selection samples. The colors will vary slightly from Epoxy.com Standard Colors due to the conductive filler content.
Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared as outlined in Epoxy.com Surface Preparation Procedures. The Epoxy.com Technical Service Department is available to answer any questions.
Installation of Product #1 ESD-NT will vary with application. Typically spread in a single coat at 50-80 ft2 per gallon with a 25-30 mil notched Easy-Squeegee and lightly back-roll with a medium nap roller, immediately with cross rolling using a spiked roller. Optional use of a metal-tined spiked roller will improve leveling of the coating.
IMPORTANT: 20 mils is considered the minimum thickness to avoid a prominent orange peel texture, depending to some extent on using a spiked roller. Optional: Add 10% MEK or Anhydrous Isopropyl Alcohol (99%) as thinner to reduce orange peel use ONLY these specific thinners. Care should be taken to minimize the entrapment of air caused by over rolling. For complete instructions, consult Epoxy.com Technical Service.
Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner. Consult Safety Data Sheet (SDS) for safety and health precautions.
| Working Life | 20-35 min @75°F |
| Minimum Recoat Time | 12-14 hours @75°F. |
| Light Foot Traffic | 24-30 hours @75°F |
| Wheeled Traffic | 36-48 hours @75°F |
| Full Chemical and Max Resistance | 7 Days @ 75°F |
| Mix Ratio | 2 Part A to 1 Part B by Volume |
| Solids Content | 99% Solids by Volume |
| Volatile Organic Content (VOC) | <50 g/L, Compliant to low VOC |
| (EPA method 24) | Rule 1113 in all 50 states |
| Gloss (60°) | 80-90 |
| Unit Sizes Available | 3 gallons, 15 gallons |
| Shelf Live | 12 months |
| Abrasion Resistance | ASTM D4050 CS-17 Wheel, 1000 Cycles |
70-100 mgs |
| Adhesion to Concrete | ASTM D7294 | 300-400 PSI Concrete Failure varies by concrete strength |
| Flammability | ASTM D635 | Self Extinguishing |
| Hardness Shore D | ASTM D2240 | 75-80 |
| Chemical Resistance | Contact Epoxy.com Tech Support | |
| Conductivity Resistance | ANSI/ESD-S7.1 | Conductive Range: Less than 1,000,000 ohms ESD Range: Less than 1,000,000,000 ohms |
| Static Charge Decay | Mil-B-817058 | Dissipates a 5,000 volt charge to zero in < 0.1 Seconds |
Contact Epoxy.com Customer Support Department
Contact Epoxy.com Technical Support Department
After completing the application of Product #1 ESD-NT, the installer should provide the owner with the maintenance instructions. Product #1 ESD-NT is easily cleaned with neutral soaps or detergents. Contact Epoxy.com Technical Support with your additional questions.